Difference between revisions of "Quantar"

Revision as of 23:11, 3 May 2024

Quantar/Quantro info

There is a bunch of info here about the technical aspects of the Quantar Stations.

The info on the modification and changing ranges of the various modules is on the respective pages. There is some conversion info below, but it's being migrated and reformatted under the respective pages. I feel this is more logical.

If you find anything to be wrong here, please feel free to make an account and change it. I've had to lock down account creation, so you'll need to have it approved. If you want to email me directly, my email is bryan@bryanfields.net

Specifications

Quantar Specifications VHF, UHF, 800 MHz - This is the combined spec sheet for the VHF/UHF and 800 base stations.

Quantar Data Base Station Specification Sheet 800 900 MHz

ASTRO TAC QUANTAR receiver manual

Programming

Links to programming stuff

CSS 007.13.R022.0035 for EPIC4 Smart Zone SCM

WinRSS 14.08.01 Windows RSS

WinRSS 14.10.00 release July 15 2011.zip

WinRSS 14.11.00

WinRSS R14.12.00

WinRSS 14.13.00 April 2015 Current Winrss - narrowband only. Use the rsscore.dll from 14.12.00 will re-enable wideband. Or just run 14.12.00.

DIU3000 CPS/CSS software 8.00.18 30-APR-2005

Firmware

The newer SCM modules can be upgraded via SLIP connection over the tty port, or via IP over the 10Base2 connector (anyone have a hub?).

The Wireline typically will upgrade during this too, unless it has the older EPROM memory. At that point you'll have to swap the chips.

The exciter is still a hard chip swap upgrade, but programed EPROM's are $20 shipped on eBay. Unless you have more than a few to upgrade it's not cost effective to buy the programer and chips yourself.

Quantar Conventional Firmware Upgrade Package R020-14-048

SIMM Images

The SIMM has a boot1 image which is a basic bootloader (0x460-0x3ffff). This runs just after the bootstrap code (0x000 0x45f). The bootloader (boot.o) contains basic code to initialize the hardware and validate the boot2.o, sc.o and wl.o images stored in the SIMM. It also has a slip loader in it. With only the boot.o code running it's possible to reload the entire OS at 9600 baud via the front port.

The boot.o is the only code not able to be upgraded on the SIMM via SLIP/FTP. To upgrade boot.o you need to flash the SIMM directly. Normally boot.o does not matter, but it is different for IR and NIR stations. The other issue is the newer (EPIC III) SCM cards will not boot with boot.o 020.10.001, and need at least the 020.10.008 code. The newest boot code is 020.10.012, and the images below have that code on them.

Conventional Firmware for U1-U4 on the SIMM module 20.14.048

media:NIR-R020.12.048 B2-R020.14.15 B1-R020.10.12.zip -- Most current firmware, works on all SCM boards.

media:Quantar-Flash-Simm-EPIC2-NON-IR-FW-20.14.048-Boot-020.10.001.zip -- Don't use, older code for historical reference only

IntelliRepeater (IR) Firmware for U1-U8 on the two bank SIMM module 20.14.520

Media:IR-SIMM-20.14.520.zip

This is for the old B013.05.014 EPIC I firmware that would run from the 27C040 PROMs. It's here for reference, don't use it.

Media:Quantar 27C040 SCM B013.05.014 EPROM images.zip

Hacking info

How to combine the firmware into a single binary image

srec_cat -Output 20.14.038-SIMM.bin -Binary \
"U4.bin" -Binary -unsplit 4 0 \
"U3.bin" -Binary -unsplit 4 1 \
"U2.bin" -Binary -unsplit 4 2 \
"U1.bin" -Binary -unsplit 4 3

srec_cat -Output 20.14.048-SIMM.bin -Binary \
"20.14.048 - epic 2 - u4.bin" -Binary -unsplit 4 0 \
"20.14.048 - epic 2 - u3.bin" -Binary -unsplit 4 1 \
"20.14.048 - epic 2 - u2.bin" -Binary -unsplit 4 2 \
"20.14.048 - EPIC 2 - U1.bin" -Binary -unsplit 4 3


How to Split it back into a per chip image.

srec_cat 20.14.048-SIMM-920mhz.bin -Binary -split 4 0 -Output U4-920.bin -Binary
srec_cat 20.14.048-SIMM-920mhz.bin -Binary -split 4 1 -Output U3-920.bin -Binary
srec_cat 20.14.048-SIMM-920mhz.bin -Binary -split 4 2 -Output U2-920.bin -Binary
srec_cat 20.14.048-SIMM-920mhz.bin -Binary -split 4 3 -Output U1-920.bin -Binary

0x00000 is the start of boot1 

boot1 is never updated by the station.  When you go to flash the station, the ftp server an everything runs from this code.  The main sc.o code doesn't have the FTP server in it. 

0x40000 is the start of boot2  
BEBE CAFE BEBE CAFE then object name
FEED BEEF FEED BEEF is the end then  4 bytes 
EEnd of ROM
0x80000 is the start of sc.o
0018FC54 is the start of wl.o

Wireline Images

Go check out the wireline page for updated info the below is not the most current.

Wireline 20.10.816 for AT27C010 Chips. This works with the 20.14.048 Conventional Firmware

Wireline U134 Upper 20.10.816

Wireline U135 Lower 20.10.816

Exciter Images

This is the matching Exciter Image for a AM27C512 UV EPROM

Exciter 020.09.018

Code Plug format

Manuals

Quantar Satellite Receiver Instruction Manual 68P81087E25-O.pdf - This is the manual for Satellite Receiver (not AstroTac Receiver), which is basically a Quantar minus the PA/Exciter. The advantage to this is it can be used where wildcard functions are need.

Quantar Service Manual 68P81088E90-G - this is the full service manual for the Quantar/Quantro and AstroTac
Quantar RSS Manual R14.10.00

Quantar RSS Manual R14.13.00

a complete listing of service bulletins for the Quantar

The PDR3500 is basically a Quantar in a portable format using a PA from a Spectra mid power radio. The basic service manual has a diagram of the backplane and glue circuits that tie this all together. It's very interesting to read as it explains quite a bit more of how the ID resistors and SPI bus works. If you're hacking quantar's, it's a must read.

PDR 3500 Transportable Repeater Basic Service Manual

ASTRO 25 Conventional Systems System Planner ASTRO 3.1 Convl Sys.Planner

Zhone TeNSr 800 imacs-system-reference-guide-7.2.1

68P81003Y54-O Managing Network Transport Equipment

GPS Simulcast Installation Manual 68P81098E65-C

RSS Software Help file. - this is the help file from WinRSS and is quite useful for station programing tips.

Hardware info

Part numbers

Here are part numbers and what the correspond to.

Power Supplies

The -48v supplies are easy to see as they have a side to side DC breaker style switch. The Motorola/Onan column refers to the manufacturer of the PS. Many people rag on the Onan power supplies, but I've not had one fail in service yet. The Onan do have a heat activated fan, whereas the Motorola run continuously. This can be good for base use or in the lab, as the base station will not make noise unless it's keyed down for some time.

Quantar power supplies
P/N	Description	Motorola/Onan	Watts
CPN1031	48/60v input	Yes	600
CPN1049	AC no charger	Yes	265
CPN1050	AC with Charger	Yes	265
CPN1047	AC no charger	Yes	625
CPN1048	AC with Charger	Yes	625
TRN7802	12/24v DC	No	210
TRN7803	48/60v input	No	210
TRN7801	24v input	No	600
CPN1042	AC	No	700
TPN6185	AC w/Charger	?	625
TPN1186	No idea	?

BackPlane

The BackPlane modules are different for the Quantar and Quantro.

Station Control info

Station Control Module or SCM is the heart of the Quantar station. The SCM comes in different revisons known as EPIC.

EPIC I - TTN4094
EPIC II - CLN6686F
EPIC III - Note the EPIC3 will not work out of band. The modulation will be very low.
EPIC IV - This is only for the Smart Zone trunking. IT will not work for conventional
EPIC V - MCLN8447

Quantar
EPIC	P/N Type	Conv/6809	IntelliRepeater	Astro 25 Trunking ONLY
EPIC I	Board	TTN4094	TRN7900	N/A
	FRU	TLN3397	TLN3398	N/A
EPIC II	Board	CLN6961	CLN6960	N/A
	FRU	CLN1293	CLN1294	N/A
EPIC III	Board	CLN1614	N/A	N/A
	FRU	CLN1621	N/A	N/A
EPIC IV	Board	N/A	N/A	CLN7692
	FRU	N/A	N/A	DLN1229
EPIC V	Board	MCLN8426	MCLN8447	N/A
	FRU	CLN8480	CLN8479	N/A

ASTRO-TAC Receiver
EPIC	P/N Type	Conv/6809	Astro 25 Trunking ONLY
EPIC I	Board	TTN4094	N/A
	FRU	TLN3397	N/A
EPIC II	Board	CLN6873	CLN6873
	FRU	CLN1273	CLN1273
EPIC V	Board	MCLN8426	MCLN8426
	FRU	CLN8480	CLN8480

Others
EPIC	P/N Type	SecureNet	Limited	PDR 3500	DBS	ATAC 3000	ATAC9600
EPIC II	Board	CLN6961	CLN7462	CLN6686	CLN7361	CLN7361	CCN4009
	FRU		CLN1609	CLN1177	CLN1914	CLN1914	CCN1009
EPIC V	Board	MCLN8426	N/A	N/A	N/A	N/A	N/A
	FRU	Unknown	N/A	N/A	N/A	N/A	N/A

The only difference between the various versions of the EPICs (excluding EPIC IV) is the hardware is newer. There is no difference in functionality for conventional analog/astro/P25 operation.

SIMM info

The SIMM used for firmware in the Quantar EPIC 2/3 is an 80 pin SIMM and is basically unobtanimum. It is possiable to use a Motorola Console Operator Interface Module SIMM if you want to modify it.

The conventional uses 4, 29F040 chips arranged to be 32 bits wide. This means each chip stores every 4th byte.

Example we store "QUANTAR MOTOROLA" in the SIMM

Chip 1	Chip 2	Chip 3	Chip 4
Q	U	A	N
T	A	R
M	O	T	O
R	O	L	A

So if we read Chip 1 we'd see QTMR.

The IR uses a two bank SIMM with the same layout (8 chips total)

It's possible to pull these chips and read/write them if you have the right programmer. Taking advantage of this I was able to build a SIMM programmer for the soldered in place SIMM's that essentially programs one chip at a time (8bits).

80 Pin SIMM Programmer

It's not pretty but it works.

The SIMM has the ability to be upgraded via the SCM download procedure, but the IR SIMM and NON-IR SIMMs cannot be interchanged. This is do to the boot code being different. Using the SIMM programmer or the socketed SIMM you can reprogram the SIMM's for either.

SIMM-less SCM

It is possible to use 29F040 chips in the sockets on the EPIC 1 with just a flick of the Flash switch, this makes it easy to use the current Quantar Firmware in the EPIC 1 with just standard DIP chips.

In the later revision EPIC's the DIP sockets are only used for 27c040 chips which have a slightly different pinout. It's possible to use the SIMM images as u1-4 maps to U451-454 with a slight modification to the chips. Typically I'll bend up pins 1, (A18 on Flash, VPP on EEPROM) and 31 (!WE on Flash, A18 on EEPROM), and then connect a wire from the board at pin 31 to pin 1 on the chip. A connection to !WE on the chip is optional unless you want to be able to upgrade the chips. In this case you'll need to make a conection from SIMM pins 53, 29, 6, & 5 to the !WE lines on U451-U454 respectively.

The Quantar doesn't care about the ID pins on the SIMM, but I typically will tie 74, 75, 76, 79 to ground/pin 80. If you're doing an ATAC 3k, the ATAC does care about this and you need pins 76 and 79 tied to ground.

Of course the Intelerepeater and ATAC9k will not work in this configuration as they need two banks on the SIMM, so you can't do this if that's your requirement. For most ham stuff, there's no reason you need anything more than NIR code for Quantar and ATAC 3000.

Receiver

Like the rest of the unit the receivers are frequency dependent and consist of their own modules. The basic receiver has a preselector which is 4 MHz wide on VHF and 6 MHz wide on UHF.

The receiver is an excellent high side injection design (exception for 800/900 which is low side). The first IF is +21.45 MHz on VHF and +73.35 MHZ on UHF/800/900. The second IF is 455 KHz. In many cases barefoot (minus preselector) the receiver sensitivity is under -120dBm for 12 dB SINAD. Couple this with the great built in selectivity and it's truly a bullet proof design idea for high RF sites.

The receiver is pretty dumb, there is not a μP on the board, making it easier to troubleshoot. The devices receive their programming from the main CPU on the SCM via SPI bus. The two main chips are the U2500 receiver IC and U2401 PLL IC. U2401, the PLL, is a custom chip responsible for locking the VCOs to the proper frequency, and selecting the high or low VCO. U2500, the receiver IC, contains the 2nd IF/VCO and final processing of the intended signal. Unlike other designs, the receiver IC presents the recovered audio/data as two digital signals to the SCM where A/D conversion happens (if needed).

There are a couple other chips which present various

UHF R0 was added later and extends the coverage and tuning range of the unit down to 380 MHz. The preselctor for this covers the whole range as well.

Each item has more information on it's own page and covers conversions there as well.

Svc Man P/N	CLD	FRU P/N	Range	Preselector	Description
TRD6361	CLD1250	TLN3250	VHF R1	TFD6511	VHF Receiver 132-154 MHz
TRD6362	CLD1260	TLN3251	VHF R2	TFD6512	VHF Receiver 150-174 MHz
CRX4022	CRX1027	DLN1215	UHF R0	CRX4001	UHF Receiver 380-433 MHz
TRE6281	CLE1190	TLN3313	UHF R1	TLE5991	UHF Receiver 403-433 MHz
TRE6282	CLE1200	TLN3314	UHF R2	TLE5992	UHF Receiver 438-470 MHz
TRE6283	CLE1210	TLN3373	UHF R3	TLE5993	UHF Receiver 470-490 MHz
TRE6284	CLE1220	TLN3374	UHF R4	TLE5993	UHF Receiver 490-520 MHz
TRF6551	CLF1530	TLN3315	800	N/A	800 MHz Receiver 806-825 MHz
TRF6552	CLF1540	TLN3316	900	N/A	900 MHz Receiver 935-941 MHz

Exciter

The exciters contain their own CPU which communicates with the SCM over a SPI bus. This CPU runs it's own firmware and requires a socketed UV EPROM to upgrade it. This also controls the PA meeting and the bit of EEPROM in the CPU stores the alignment settings for the exciter and PA. Generally a Exciter/PA pair will not need to be realigned if moved from one chassis to another, although it should be checked.

Svc Man P/N	CLD	FRU P/N	Range	Description
TLD9831	CLD1270	TLN3252	VHF R1	VHF Exciter 132-154 MHz
TLD9832	CLD1280	TLN3253	VHF R2	VHF Exciter 150-174 MHz
CLX4000	CLX1000	DLN1214	UHF R0	UHF Exciter 380-433 MHz
TLE5971	CLE1230	TLN3305	UHF R1	UHF Exciter 403-433 MHz
TLE5972	CLE1240	TLN3306	UHF R2	UHF Exciter 438-470 MHz
TLE5973	CLE1210	TLN3375	UHF R3	UHF Exciter 470-490 MHz
TLE5974	CLE1220	TLN3376	UHF R4	UHF Exciter 490-520 MHz
TLF6920	CLF1510	TLN3307	900	800 MHz Exciter 850-870 MHz
TLF6930	CLF1520	TLN3308	900	900 MHz Exciter 935-941 MHz

Station Access Module

Check here for SAM info

Troof Table

There is a ID code representing the exciter type, it consists of R3700 to R3710. These are either pull up or down resistors on a 6 bit code and are identified on the schematic on the left side of U3700, the μP. Below is the table in MSB-LSB format, with a 1 being high (5v) and a 0 being a low (0v).

Dip switch!	Band!	Binary!	Notes in the RSS!
0	VHF_R1	000000
1	VHF_R2	000001	VHF R2 SL
2	UHF_R1	000010
3	UHF_R2	000011
4	800	000100
5	VHF_R3	000101	sl
6	VHF_R4	000110
7	VHF_R1	000111
8	VHF_R2	001000	VHF R2 FL
9	VHF_R3	001001
10	VHF_R4	001010
11	900	001011
12	UHF_R3	001100
13	UHF_R4	001101
14	blank	001110
15	blank	001111
16	blank	010000
17	blank	010001
18	blank	010010
19	blank	010011	uhf r0 from book
20	blank	010100
21	blank	010101
22	blank	010110
23	blank	010111
24	blank	011000
25	blank	011001
26	blank	011010
27	blank	011011
28	blank	011100
29	blank	011101
30	blank	011110
31	blank	011111
32	blank	100000
33	blank	100001
34	blank	100010
35	blank	100011
36	blank	100100
37	blank	100101	boot
38	blank	100110
39	blank	100111
40	blank	101000
41	blank	101001
42	blank	101010
43	blank	101011
44	blank	101100
45	blank	101101
46	blank	101110
47	blank	101111	"RSS only"
48	blank	110000
49	blank	110001
50	blank	110010
51	blank	110011
52	blank	110100	RAP says VHF_R2 SL
53	blank	110101
54	blank	110110
55	blank	110111
56	blank	111000
57	blank	111001
58	blank	111010
59	blank	111011
60	blank	111100
61	blank	111101
62	blank	111110
63	INVALID	111111	Exciter is in reset all LED's are on and the PA fans turn on

PDR3500

The PDR3500 is a portable version of the repeater. Here's some details and internal pics of it.

Power Amp

The power amps are actually a cool design.

Their are two basic power amps, a 25W, and a 100/110/125w (depending on band). The power amps all use the same general board layout, with the frequency dependent parts separate from the support components. The 25W PA is a passively cooled unit with a massive heatsink, while the 100/110/125W unit has active cooling with a horizontal heatsink and two cooling fans moving air front to back.

There are a couple different revisions of the PA's so the main PCB has changed a bit over time.

PCB Layout High Power

PCB Layout Low Power

[[|thumbnail|center]]

The PA doesn't contain any CPU, it's controlled via the exciter CPU with basic analog level lines going over to the exciter. Some of what's measured by the exciter

Intermediate PA drive level - this is the output of the IPA to the final PA pallet
Driver PA Level - output of the final PA before the circulator (FPA_DETECT).
TX Power Forward - Output measured at the output of the Low Pass Filter
TX Power Reverse - Reflected Power from the antenna port
OMNI voltage - this is the control voltage on the IPA which comes from the SCM as a 0-5V control signal (V_CONT). This 0-5v controls a transistor making a 0-14v signal to provide the gain of the IPA. This is the basis of the power control. The Control Voltage from the SCM is only present during keydown.
IPA Current detect
DPA Side A & B current sense
Temperature of the PA 3.981v is 79f 2.0 is about 170f This looks like an 8 bit value with 0xFF == 5.000 V or .019608v per bit.
- PA Fans turn on at 2v and off at 2.90v.
Fan on/off and alarm
PA_ID bits A & B - resistor divider that programs to reference voltages in .5v increments to ID the PA hardware to the exciter.

All these are measured over an TDM bus that selects each at a 200ms interval using a single analog input on the exciter CPU.

PA types

Svc Man P/N	Other P/N	Rated Power	Range	Description
CLD1295A			120?	VHF?	Unknown
TLD3102	CLD1299	125	VHF R2	VHF PA
TLD3110		25	VHF R1/R2	VHF PA
TLD3101	TLN3379 CLD1298	125	VHF R1 (NEW)	VHF PA
CTX1146	DLN1216	110	UHF R0	Second Generation UHF PA 380-433 MHz
TTE2061	TLN3444	110	UHF R1	First Generation UHF PA 403-433 MHz
CLE6164	Example	110	UHF R1	Second Generation UHF PA 403-433 MHz
TTE2062	TLN3446	110	UHF R2	First Generation UHF PA 438-470 MHz
CLE6165	CLE1308	110	UHF R2	Second Generation UHF PA 438-470 MHz
TTE2063		110	UHF R3	First Generation UHF PA 470-490 MHz
TTE6373		110	UHF R3	Second Generation UHF PA 470-490 MHz
TTE2064		100	UHF R4	First Generation UHF PA 490-520 MHz
TTE6374		100	UHF R4	Second Generation UHF PA 490-520 MHz
CTF1091A/TLF1930	TLN3442	100	800	800 MHz 100W PA
CTF1092A/TLF1800	TLN3299	100	900	900 MHz 100W PA

PA Type	PA_ID_A	PA_ID_B	R4162	R4163	R4164	R4165	Official?
900 100W	3.0	.5	20.5k	10k	1k	OPEN	YES
800 100W	0.5	1.0	OPEN	0	1.5K	15K	YES
800 20W	0.0	1.0	OPEN	1k	1.5K	15K	YES
UHF 110W R0	0.0	1.5	OPEN	0	390	1k	YES
UHF 110W R1	1.0	0.5	15k	1.5k	560	10k	YES
UHF 110W R2	1.5	0.5	1k	390	100	1k	YES
UHF 110W R3	3.0	1.0	2.2k	2.7k	1.5k	15k	YES
UHF 100W R4	3.5	1.0	18k	15k	1.5k	15k	YES
UHF 25W R1	5.0	0.0	33.2k	OPEN	0	OPEN	YES
UHF 25W R2	0.0	0.5	OPEN	0	1k	OPEN	YES
VHF 125W R1	3.0	0.0	20.5k	10k	0	OPEN	YES
VHF 125W R2	0.0	0.0	OPEN	0	0	OPEN	YES
VHF 25W R1/R2	4.5	0.0	12k	68k	0	OPEN	YES
VHF 25W R1	3.5	0.0				NO

UHF 110W Generation 1 UHF 110W Generation 2

CTF1091A 100 W 800 MHz CTF1092A 100 W 900 MHz CTX1146A Range 0 Power Amplifier TLF1800B 100W Power Amplifier Module TLF1930C 100W Power Amplifier Module TLF1940B 20W Power Amplifier Module TTE2061A 110W Power Amplifier UHF R1 TTE2062A 110W Power Amplifier UHF R2 TTE2063A 110W Power Amplifier UHF R3 TTE2064A 110W Power Amplifier UHF R4

TLE2511A/ 110W Power Amplifier Module TLE2512A TLE2521 TLE2572 TLE2731B 25W Power Amplifier Module UHF R1 TLE2732B 25W Power Amplifier Module UHF R2 TLD3101G 125W Power Amplifier Module VHF R1 TLD3102G 125W Power Amplifier Module VHF R2 TLD3110C 25W Power Amplifier Module VHF R1/R2 CLX4002A 100/110W Power Amplifier Module (UHF; R1-R4) CLE6164A 100/110W Power Amplifier CLE6165A Module (UHF; R1-R4)

TTE6373A/ 100/110W Power Amplifier TTE6374A Module (UHF; R1-R4)

Troubleshooting notes

Most of the time the PA's are rock solid. I have some notes below on trouble shooting them.

swap with a known good PA, does the problem go away?
Align the PA/init the PA
Check the amp draw on both sides
Always run it at 100% rated power for testing.

Silly PA syndrome

Some times people run the PA at lower output to "make it easier on it". So long as cooling is working, running it at rated output is the least stressful way to operate it. Running at reduced power output is actually harder on the PA.

The PA has an intermediate stage and a final amp stage. The final amp runs at the same gain level all the time. The power out is changed by varying the IPA voltage. As this is done via a linear regulator, as the power output goes down, there is more and more power dissipated in the Q4100 (UHF) pass transistor. This is due to running the IPA at lower and lower voltage to drop the power to the final. Typically what happens is a station will key up, then fail and try to fall back in power, but this just makes it worse.

What I've done to test this:

Run the PA at 120% (ie 150w output) just for a bit. ie init it and align it for 110w = 130W.
Test the station, key it down and check that it's solid for 2-3 min.
check the value of the OMNI Voltage in the station metering.

If this is good, replace the Q4100, and check the operation of the power control circuits (q4101, V_CONT, VOMNI).

This normally fixes it.

@@ Line 11: / Line 11: @@
 [[Media:Quantar Specifications VHF, UHF, 800 MHz.pdf|Quantar Specifications VHF, UHF, 800 MHz]] - This is the combined spec sheet for the VHF/UHF and 800 base stations.
-[[Media:Quantar Data Base Station Specification Sheet 800 900 MHz.pdf|Quantar Data Base Sation Specification Sheet 800 900 MHz]]
+[[Media:Quantar Data Base Sation Specification Sheet 800 900 MHz.pdf|Quantar Data Base Station Specification Sheet 800 900 MHz]]
 [[Media:ASTRO TAC QUANTAR receiver manual.pdf|ASTRO TAC QUANTAR receiver manual]]
@@ Line 29: / Line 29: @@
 [[Media:WinRSS R14.12.00.zip| WinRSS R14.12.00]]
-[[Media:WinRSS_R14.13.00.zip|WinRSS 14.13.00 April 2015]] Current Winrss
+[[Media:WinRSS_R14.13.00.zip|WinRSS 14.13.00 April 2015]] Current Winrss - narrowband only.  Use the rsscore.dll from 14.12.00 will re-enable wideband. Or just run 14.12.00.
 [[Media:DIU CSS Installation.zip|DIU3000 CPS/CSS software 8.00.18 30-APR-2005]]
@@ Line 93: / Line 93: @@
 srec_cat 20.14.048-SIMM-920mhz.bin -Binary -split 4 3 -Output U1-920.bin -Binary
 x00000 is the start of boot1
+boot1 is never updated by the station.  When you go to flash the station, the ftp server an everything runs from this code.  The main sc.o code doesn't have the FTP server in it.
 x40000 is the start of boot2
 BEBE CAFE BEBE CAFE then object name
@@ Line 120: / Line 123: @@
 === Manuals ===
+* [[media:Quantar Satellite Receiver Instruction Manual 68P81087E25-O.pdf|Quantar Satellite Receiver Instruction Manual 68P81087E25-O.pdf]] - This is the manual for Satellite Receiver (not AstroTac Receiver), which is basically a Quantar minus the PA/Exciter.  The advantage to this is it can be used where wildcard functions are need.
-* [[media:Service_manual.pdf]]
+* [[media:Service_manual.pdf|Quantar Service Manual 68P81088E90-G]] - this is the full service manual for the Quantar/Quantro and AstroTac
 * [[media:Quantar RSS Manual R14.10.00.pdf|Quantar RSS Manual R14.10.00]]
@@ Line 128: / Line 132: @@
 * [[:Category:Quantar Service Bulletin |a complete listing of service bulletins for the Quantar]]
-The PDR3500 is basically a quantar in a portable format using a PA from a Spectra mid power radio.  The basic service manual has a diagram of the backplane and glue circuits that tie this all together.  It's very interesting to read as it explains quite a bit more of how the ID resistors and SPI bus works.  If you're hacking quantar's, it's a must read.
+The [[PDR 3500|PDR3500]] is basically a Quantar in a portable format using a PA from a Spectra mid power radio.  The basic service manual has a diagram of the backplane and glue circuits that tie this all together.  It's very interesting to read as it explains quite a bit more of how the ID resistors and SPI bus works.  If you're hacking quantar's, it's a must read.
 * [[Media:PDR 3500 Transportable Repeater Basic Service Manual.pdf|PDR 3500 Transportable Repeater Basic Service Manual]]
+* [[Media:ASTRO 25 Conventional Systems System Planner ASTRO 3.1 Convl Sys.Planner.pdf|ASTRO 25 Conventional Systems System Planner ASTRO 3.1 Convl Sys.Planner]]
+* [[Media:Zhone TeNSr 800 imacs-system-reference-guide-7.2.1.pdf|Zhone TeNSr 800 imacs-system-reference-guide-7.2.1]]
+* [[Media:68P81003Y54-O Managing Network Transport Equipment.pdf|68P81003Y54-O Managing Network Transport Equipment]]
+* [[Media:GPS Simulcast Installation Manual 68P81098E65-C.pdf|GPS Simulcast Installation Manual 68P81098E65-C]]
+* [[Winrss help|RSS Software Help file.]] - this is the help file from WinRSS and is quite useful for station programing tips.
 == Hardware info ==
@@ Line 182: / Line 196: @@
 * [[EPIC 1|EPIC I  - TTN4094]]
-* EPIC II
+* [[EPIC II|EPIC II - CLN6686F]]
 * EPIC III - Note the EPIC3 will not work out of band.  The modulation will be very low.
 * EPIC IV - '''This is only for the Smart Zone trunking.  IT will not work for conventional'''
@@ Line 295: / Line 309: @@
 Like the rest of the unit the receivers are frequency dependent and consist of their own modules.  The basic receiver has a preselector which is 4 MHz wide on VHF and 6 MHz wide on UHF.
-The receiver is an excellent high side injection design (exception for 800/900 which is low side).  The first IF is +21.45 MHz on VHF and +73.35 MHZ on UHF/800/900.  The second IF is 455 KHz.  In many cases barefoot (minus preselector) the receiver sensitivity is under .112μV (-126 dBm) for 12 dB SINAD.  Couple this with the great built in selectivity and it's truly a bullet proof design idea for high RF sites.
+The receiver is an excellent high side injection design (exception for 800/900 which is low side).  The first IF is +21.45 MHz on VHF and +73.35 MHZ on UHF/800/900.  The second IF is 455 KHz.  In many cases barefoot (minus preselector) the receiver sensitivity is under -120dBm for 12 dB SINAD.  Couple this with the great built in selectivity and it's truly a bullet proof design idea for high RF sites.
 The receiver is pretty dumb, there is not a μP on the board, making it easier to troubleshoot.  The devices receive their programming from the main CPU on the SCM via SPI bus.  The two main chips are the U2500 receiver IC and U2401 PLL IC.  U2401, the PLL, is a custom chip responsible for locking the VCOs to the proper frequency, and selecting the high or low VCO.  U2500, the receiver IC, contains the 2nd IF/VCO and final processing of the intended signal.  Unlike other designs, the receiver IC presents the recovered audio/data as two digital signals to the SCM where A/D conversion happens (if needed).
@@ Line 312: / Line 326: @@
 | TRD6361 || CLD1250 || TLN3250 || VHF R1  || [[VHF Preselector|TFD6511]] || [[VHF Receiver|VHF Receiver 132-154 MHz]]
 |-
-| TRD6362 || CLD1260 || TLN3251 || VHF R2 || [[VHF Preselector|TFR6512]] || [[VHF Receiver|VHF Receiver 150-174 MHz]]
+| TRD6362 || CLD1260 || TLN3251 || VHF R2 || [[VHF Preselector|TFD6512]] || [[VHF Receiver|VHF Receiver 150-174 MHz]]
 |-
 | CRX4022 || CRX1027 || DLN1215 || UHF R0 || [[UHF Preselector|CRX4001]] || [[UHF R0 Receiver|UHF Receiver 380-433 MHz]]
@@ Line 500: / Line 514: @@
 |}
-=== Power Amp ===
+=== [[PDR 3500|PDR3500]] ===
+The PDR3500 is a portable version of the repeater.  Here's some details and internal pics of it.
+== Power Amp ==
 The power amps are actually a cool design.
@@ Line 522: / Line 539: @@
 * IPA Current detect
 * DPA Side A & B current sense
-* Temperature of the PA
+* Temperature of the PA 3.981v is 79f 2.0 is about 170f This looks like an 8 bit value with 0xFF == 5.000 V or .019608v per bit.
+** PA Fans turn on at 2v and off at 2.90v.
 * Fan on/off and alarm
 * PA_ID bits A & B - resistor divider that programs to reference voltages in .5v increments to ID the PA hardware to the exciter.
@@ Line 531: / Line 549: @@
 {| class="wikitable sortable"
 |-
 ! Svc Man P/N !! Other P/N !! Rated Power !! Range !! Description
+|-
+| CLD1295A || || || 120? || VHF? || Unknown
+|-
+| TLD3102 || CLD1299 || 125     || VHF R2 || [[VHF PA| VHF PA]]
+|-
+| TLD3110 ||  || 25    || VHF R1/R2 || [[VHF PA| VHF PA]]
+|-
+| TLD3101 ||  TLN3379 CLD1298 || 125    || VHF R1 (NEW) || [[VHF PA| VHF PA]]
 |-
 | CTX1146 || DLN1216 || 110     || UHF R0  || [[Second Generation PA|Second Generation UHF PA 380-433 MHz]]
@@ Line 619: / Line 645: @@
 TTE6374A Module (UHF; R1-R4)
-== Conversions ==
+=== Troubleshooting notes ===
-Work in progress on moving Qunatar bands.
-These are depreciated, refer to the pages on each FRU.
-Going to move this to the various exciter/PA/receiver pages verses having its own page.
-=== VHF R2 to R1 ===
-Looks like it should work
-==== Exciter ====
-Parts difference and re-tune the VCO's
-==== Amplifier ====
-===== 25W PA =====
-This covers both R1 and R2.
-===== 125W PA MODELS TLD3101/TLD3102 =====
-The 125W PA is the same PA pallet, Low Pass Filter, and IPA.  The circulator is different, and about 300 from MOTO.  Should be a matter of changing the ID bits
-CLD1298 and CLD1299 newer 125W PA's look like they are them same.
+Most of the time the PA's are rock solid.   I have some notes below on trouble shooting them.
+* swap with a known good PA, does the problem go away?
+* Align the PA/init the PA
+* Check the amp draw on both sides
+* Always run it at 100% rated power for testing.
-=== VHF R2 to 220 MHz ===
-Software works, it's putting the R4 code plug in, verified the 212.5 cross over frequency for the VCO's.  Still need to work out some bugs in it.  Should use the 800 MHz for the 220 MHz programing.
+===='''Silly PA syndrome''' ====
+Some times people run the PA at lower output to "make it easier on it".  So long as cooling is working, running it at rated output is the least stressful way to operate it.  Running at reduced power output is actually harder on the PA.
-Exciter is working.
+The PA has an intermediate stage and a final amp stage.  The final amp runs at the same gain level all the time.  The power out is changed by varying the IPA voltage.  As this is done via a linear regulator, as the power output goes down, there is more and more power dissipated in the Q4100 (UHF) pass transistor.  This is due to running the IPA at lower and lower voltage to drop the power to the final.  Typically what happens is a station will key up, then fail and try to fall back in power, but this just makes it worse.
-PA is a complete rebuild, working on it, circulator is being reworked.  The A+B voltage feeds are a problem.
+What I've done to test this:
-Right now it keys up, and then shits the bed as the PA is fail.  I've tested it by putting good voltage on the IPA, PA, FPA and SWR sense lines.  Still doesn't like the PA not drawing current and craps out after like 30 seconds, but it was long enough to test the output from the exciter, it's 13.5 dBm on the Rigol.
+* Run the PA at 120% (ie 150w output) just for a bit.  ie init it and align it for 110w = 130W.
+* Test the station, key it down and check that it's solid for 2-3 min.
+* check the value of the OMNI Voltage in the station metering.
-Receiver VCO is working, need to modify the image filter and test.
+If this is good, replace the Q4100, and check the operation of the power control circuits (q4101, V_CONT, VOMNI).
+This normally fixes it.
 [[Category:Quantar]]