UHF Preselector

Basics

The UHF preselector is a 3 pole, low insertion loss (1.2 dB) 4 MHz wide filter. In practice this is closer to 5MHz wide.

The preselector varies based on the band of the RX as follows

P/N	Range	Description
CRX4001	UHF R0	UHF Preselector 380-433 MHz
TLE5991	UHF R1	UHF Preselector 403-433 MHz
TLE5992	UHF R2	UHF Preselector 438-470 MHz
TLE5993	UHF R3 & R4	UHF Preselector 470-520 MHz

Note R3 and R4 use the same preselector. The preselector hooks up to the RX input and can be removed for testing.

Preselector in receiver

The internal design of the preselector is basically a tubular inductor and a top capacitance hat. Interesting to note the coupling takes place at the low side vs. the normal high side. The center of this hat/inductor has a hole into which the tuning screws slide in to/out of. The R0 preselector has a much longer screw, and the front panel has a protective metal part protecting the protruding parts.

• 

  Range 0 Receiver front

The bottom of the preselector has T10 size screws on it and they need to be tightened and loosened in order of the numbers on the bottom plate. Once apart the variance in the length of the cap hat should be noticed showing the range of the preselector.

Range	Cap Hat length (inches)
UHF R0
UHF R1	.880
UHF R2	.650
UHF R3 & R4	.437*

Note the R3 and R4 is based on measurement from a friend, not measured with a caliper.

• 

  R0 in front vs a R3/4 preselector

• 

  Preselector diagram

Patterns of preselectors measured with a spectrum analyzer. Note the bit of ripple in the pass band. Motorola sells a probe to be used to align the preselector via alternate peaking and diping it, but it's much easier to tune on a spectrum analyzer/tracking generator. This has the advantage allowing you to tune for the exact pass band needed. In many cases it's advantageous to tune the center off of the frequency. I find it's easy to tune the entire US 440 ham band input range as a CF of 447.5.

• 

  UHF R2

• 

  Quantar R0 at 380 MHz

• 

  Quantar R0 at center

• 

  Quantar R0 at 437 MHz

• 

  Tuning a R0 preselector

Modification

Two styles of modification have been attempted on these preselectors to raise the frequency. Lowering the frequency has not been attempted (ie. R4 to R2), and all focus on moving R0/1 to R2, though the same techniques would work to move to R3/4.

Method 1: Shorting the Rod

Shortening the rods was attempted on the first modification of the R0 to R2 preselector. The cap hats were removed and the center rods were ground down .270" on each rod.

This became a problem as the rods are made of silver plated copper plated aluminum, which makes grinding a hard thing to do. It removed the tinned part of the rods where they solder to the cap hats, and the alignment "key" notched into the top of the rods. The final result was a filter which had a bit more ripple and wider than desired, but with good insertion loss.

I suspect the width was changed mostly due to moving the cap hats lower in the housing.

• 

  R0 preselector during modification

• 

  Quantar R0 converted to R2 by cutting tubes showing post modification drilling to lower capacitance

• 

  Quantar R0 converted to R2 via tub cutting sweep

• 

  R0 converted to R2 by tube cutting over lay on real R2

For the R0 filter at normal frequency the tuning slugs should be roughly as follows:

Center	length sticking out (inches)	insertion loss
380 MHz	.275	.65 dB
433 MHz	1.140	.60 dB
437 MHz	1.200	.40

After grinding the stubs down it was necessary to use an aluminum flux and soldering iron to get the solder to adhere to the metal of the studs. This flux destroyed my Metcal tip and it had to be replaced, at a cost of $30. After this it was easy to use a heat gun and reflow the solder on the caps. The issue here is to make sure they line up as the notches are removed from the stubs during grinding.

Over all this method works, but it's much easier to cut the hats down in length.

Method 2: shortening the cap length

This is the preferred method to raise the frequency as it's more in line with the construction Motorola uses.

The procedure is as follows:

1. Open the preselector and set aside screws and top case.
2. Secure the bottom to a work surface and pre-heat the first cap

• 

3. Using a hot air gun heat the first cap up and remove it.
• 
4. Do the same for the rest of the caps
5. Once cooled down it's time to grind the caps to .650"
• 
• 

I find it's best to score a line around the cap before grinding. You can also use a band saw to remove the majority of the metal first and then clean it up on the belt/circular sander. Clean up the rough cut on a fine sander and debur if necessary.

Remember you can only remove material, so check each corner for proper length. The length is not that critical (1/16"); try to get it as close a possible.

• 

6. Once all caps are the proper length, clean them in water/detergent bath. Ensure no grindings are left or able to flake off.
• 
7. Set the caps on the stubs, noting the alignment notch.

• 

There is still much play in the alignment, and they may need to be adjusted once reflowed.

8. Apply a dab of flux to the joint
9. Reflow the solder with the heat gun, and add silver bearing solder to ensure a nice fillet joint.
• 
• 
10. Do this for all caps
11. Allow to cool and then deflux the joints
12. Reassemble the case, and tighten screws in numerical order.
13. Test tuning and insertion loss at 438, 454, and 470 MHz. Loss should be a dB or less at all frequencies.
• 

  Quantar R1 to R2 UHF RX filter

• 

  Completed R1 to R2

•