Difference between revisions of "IMBE Link"
| Line 50: | Line 50: | ||
= Features defined = | = Features defined = | ||
| + | |||
| + | == Talk Group Scan == | ||
| + | |||
| + | This describes the version of scanning in version 1.0 | ||
| + | In version 1.0 there is no talkback planned. A user will need to select the proper talkgroup via radio or by remote control via keypad. | ||
| + | |||
| + | A local user keying up will preempt all scan (Priority/Normal) and pause scan until they unkey. | ||
| + | |||
| + | A timer, Local Key (Lk), will be started when a user keys down and if the user stays keyed for greater than the value of this timer, scan shall be paused for the local users of the repeater. | ||
| + | |||
| + | A second timer Scan Holdoff (Sh), is started when a local user unkeys and scan is paused. When this timer expires scan shall resume. | ||
| + | |||
| + | * Lk is 10 s | ||
| + | * Sh is 300 s | ||
| + | |||
| + | |||
| + | |||
| + | === From the network === | ||
| + | |||
| + | Scanning should be allowed to define "N" talkgroups with a priority TG list. | ||
| + | |||
| + | Prior to beginning scan, a list of scan talk groups is built and ordered. The Active Talkgroup is the currently active scanned talkgroup. The Candidate is the talkgroup to be switched to. | ||
| + | |||
| + | There are two timers which may be defined in milliseconds. A value of 0 disables the timers in the logic. | ||
| + | |||
| + | * Scan Active = Sa = 10000 ms | ||
| + | * Scan Dwell = Sd = 2000 ms | ||
| + | |||
| + | Timer Scan Active determines how long the Active Talkgroup will be Active for. Upon the expiry of the timer, the Candidate will become the Active and the timer will reset. | ||
| + | |||
| + | Scan dwell is started upon the Active Talkgroup unkeying. It is held in reset while keyed. When this timer expires the Candidate will become active and the Scan Active timer will reset. | ||
| + | |||
| + | The Candidate is determined at the time of the Sa/Sd timer expiry by looking at the current active talkgroups from the scan list. The Active channel is a pointer in this list and the next active talkgroup will be the Candidate. | ||
| + | |||
| + | ==== Priority Scan ==== | ||
| + | |||
| + | A talkgroup may be defined as a Priority Talkgroup in the scan configuration. | ||
| + | |||
| + | In the event this talkgroup becomes active, the scan loop shall be stopped and the priority talkgroup immediately selected. | ||
| + | |||
| + | There will be two timers: | ||
| + | * Priority Active = Pa = 10000 ms | ||
| + | * Priority Dwell = Pd = 2000 ms | ||
| + | |||
| + | Timer Priority Active determines how long the Priority Talkgroup will be Active for. Upon the expiry of the timer, the normal scan will start. | ||
| + | |||
| + | Priority Dwell is started upon the Priority Talkgroup unkeying. It is held in reset while keyed. When this timer expires the normal scan will start. | ||
| + | |||
| + | The Priority Scan may be configured to use | ||
| + | |||
| + | Multiple levels of priority may be defined and a higher priority talkgroup will preempt the lower priority scan. | ||
Revision as of 22:34, 24 November 2017
This is the working page for IMBE Link.
Contents
Features
1.0
First version, needs to incorporate the basics of PNXmono, but in a modular format.
- config file in a traditional unixy format. No stupid C# bullshits
- Support for p25 data via STUN to cisco doing HDLC to the 9600 bps quantar v.24 interface.
- Two operational modes
- Traditional link, where the quantar does local repeat and the application handles network linking.
- Base station mode, the quantar does not repeat anything, the app repeats all data to the quantar, like an analog controller.
- In base mode, it can limit encrypted audio locally too, or force rewriting of talkgroup/messages
- Support for talk group scanning
- This would be a registration and priority matrix for individual talk groups
- support for talk back with ability to define the hang time
- Ability to block encryption or allow encryption (force encryption?)
- Courtesy tones as files - allow them to be defined
- Proxy of v.24 frames, only the IMBE data should be passed to the Quantar, control data should be stripped out
- prevents channel changes
- mute when RSSI/QOI value is below a given value (perhaps play a tone here?)
- stats collected and ASTRO ID recorded
- improved logging and debugging
- output status of system via named pipe/logic on pi.
- this would be used to block the system on P25 only for a set period of time.
- Could be accomplished via channel change too.
- Ideally would make the mixed mode operation easier without as many wildcard functions.
2.0
- FDTI to Quantar v.24 interface.
- recording of conversations and metadata
- Bridge system
- * This would be a confederation of linking and registration servers to reflect the traffic
- System Wide Stats dashboard
3.0
- Asterisk channel driver
Features defined
Talk Group Scan
This describes the version of scanning in version 1.0 In version 1.0 there is no talkback planned. A user will need to select the proper talkgroup via radio or by remote control via keypad.
A local user keying up will preempt all scan (Priority/Normal) and pause scan until they unkey.
A timer, Local Key (Lk), will be started when a user keys down and if the user stays keyed for greater than the value of this timer, scan shall be paused for the local users of the repeater.
A second timer Scan Holdoff (Sh), is started when a local user unkeys and scan is paused. When this timer expires scan shall resume.
- Lk is 10 s
- Sh is 300 s
From the network
Scanning should be allowed to define "N" talkgroups with a priority TG list.
Prior to beginning scan, a list of scan talk groups is built and ordered. The Active Talkgroup is the currently active scanned talkgroup. The Candidate is the talkgroup to be switched to.
There are two timers which may be defined in milliseconds. A value of 0 disables the timers in the logic.
- Scan Active = Sa = 10000 ms
- Scan Dwell = Sd = 2000 ms
Timer Scan Active determines how long the Active Talkgroup will be Active for. Upon the expiry of the timer, the Candidate will become the Active and the timer will reset.
Scan dwell is started upon the Active Talkgroup unkeying. It is held in reset while keyed. When this timer expires the Candidate will become active and the Scan Active timer will reset.
The Candidate is determined at the time of the Sa/Sd timer expiry by looking at the current active talkgroups from the scan list. The Active channel is a pointer in this list and the next active talkgroup will be the Candidate.
Priority Scan
A talkgroup may be defined as a Priority Talkgroup in the scan configuration.
In the event this talkgroup becomes active, the scan loop shall be stopped and the priority talkgroup immediately selected.
There will be two timers:
- Priority Active = Pa = 10000 ms
- Priority Dwell = Pd = 2000 ms
Timer Priority Active determines how long the Priority Talkgroup will be Active for. Upon the expiry of the timer, the normal scan will start.
Priority Dwell is started upon the Priority Talkgroup unkeying. It is held in reset while keyed. When this timer expires the normal scan will start.
The Priority Scan may be configured to use
Multiple levels of priority may be defined and a higher priority talkgroup will preempt the lower priority scan.
