Difference between revisions of "Waris"

From W9CR
Jump to navigation Jump to search
Line 62: Line 62:
 
This is easiest with CP tool and a hex editor.   
 
This is easiest with CP tool and a hex editor.   
  
First upgrade the Firmware using the firmware update.
+
First upgrade the Firmware using the firmware update.  This will load the default codeplug back in the radio.
   
 
  
The easiest way to mod this is using the 255 channel srecord.
+
Read the radio using the CP tool and save the binary codeplug.  I typically will read this from 0x0000 to 0x1000 which will capture the entire default codeplug (Tuning, Features, and Programing).  Save this file and set is aside for safe keeping.  If anything goes wrong, you can blow it back into the radio and restore it to defaults with out needing to retune.
  
# backup up your tuning in the global tuner program!
+
Now open up a copy of this code plug and edit it based on the Codeplug Map for the feature blocks.  This is from 0x280 to 0x2ff.
# backup your codeplug!
 
# open the waris codeplug tool and load the new file.
 
# push the file (both application and the other check box) to the radio.
 
# set the country to USA in the codeplug tool.
 
# open up the tuner and read the radio.
 
# set the serial number, capitalization matters!
 
# close tuner
 
# open tuner and load your backup file.
 
# push the backup into the radio.
 
# close tuner and open it again.
 
# read the radio in tuner.  try setting squelch, you should see a bunch of different frequencies now vs just one.  If you do come back and align it later
 
# close tuner
 
# open the CPS.
 
# push your backup into it. (click ok on the upgrade dialog box that pops up)
 
# now read the radio back into CPS to get the codeplug merge, save this as your new code plug.
 
# check the number of personalities you can add.
 
  
Try messing with the squelch in tuner.  I've found a good value is -128 dBm for hams.  My radio is -124 dBm for 12db SINAD so this is about 6 dB SINAD at -128, very noisy but understandable.  Auto tune makes this really easy.  You can always put a button to set the squelch to tight.
+
You'll need to change the following parts:
  
I've found I needed to play with the RSSI settings too, as the S meter was setup for commercial strong signal service.
+
# Serial number, ASCII spaces are blank (optional)
 +
# Channel step needs to be 0x01
 +
# Upper Frequency: 0x5F50 for 225 MHz
 +
# Signaling: 0xFF is everything enabled (MDC, QCII, DTMF) for trunking and conventional
 +
# Conventional Personalities: 0xFF for 255 channels
 +
 
 +
Once this is done, be sure the checksum 8 on both FDB blocks are 5A.  You will need to adjust the checksum bytes for this.
 +
 
 +
Open this file with the CP tool and put 0x280 to 0x2ff into the radio, no need to write the entire file.  This makes it easy to do many units at once, just blow the Feature Block in, while leaving the tuning and programing alone. 
 +
 
 +
You'll need to now tune the 20 and 25 KHz squelch settings in the tuner software.  The issue here is the tuner software will not let you select the 20 and 25 KHz from the drop down menu.  Using Winabler this can capture the tuner menu and enable these. 
 +
 
 +
I use the auto squelch setup and found a good value is -127.5 dBm for hams.  My radio is -124 dBm for 12db SINAD so this is about 6 dB SINAD at -128, very noisy but understandable.  Auto tune makes this really easy.  You can always program a button to set the squelch to tight in CPS.
 +
 
 +
I've found I needed to play with the RSSI settings too, as the S meter was setup for commercial strong signal service.  I've only seen this with certian 220 radios.
 +
 
 +
It's also a good idea to check the frequency/modulation/power out alignments too.  The CDM1550's from the New Jersey Turnpike all were aligned wrong for the power output, and we 20W out when set for 30W.  Align it in tuner properly, and then use CPS to lower the power if you want.
 +
 
 +
If you've set the serial number to blank, it's a good time to set it to what you want in tuner before you disconnect.
 +
 
 +
Once you're done with all this, you should have a great radio that covers 216-225 MHz, wide band FM, MDC/QCII/DTMF, 30W power out, and damn sensitive squelch.
  
 
== Code Plug Map ==
 
== Code Plug Map ==

Revision as of 00:38, 4 December 2016

Waris

This was originally put together when I got into the HT1250 200 MHz radios. They modified ok, but the way of doing it as suggested left much to be desired, and the DTMF pad didn't work and the radios were narrow band only.

Over time, I've gotten more into these with the CDM1250/1550 and other waris series radios. I've not seen any of the European ones, but I've been working with the US versions for FM service in ham radio.

What I've found is the radios features are determined by the "codeplug" settings. This is simply a packed (hex) data written into the eeprom chip of the radio containing tuning, feature and programing data. This is the same area the programing data from CPS is written in, but CPS is unable to change it. The majority of modification of these radios to amateur service is done with modifications to the codeplug. The codeplug layout appears to be the same for most US versions of the radios, but there are some which are different.



HT1250LS+ 220 700MHz Service Manual

220 HT1250ls and CDM 1550ls

This is the same as any other to modify to the amateur service from a software perspective. The issue is these radios are narrow band only on the receive path, as the 200 MHz band was never used for 25 KHz channels. Transmit will support wide band (and must be aligned for wide band first!) The IF filters simply need to be swapped with their wide band parts and wide band receive alignment performed.

Hardware Mod

Their are 3 filters in the radio, 1 at 44.85 MHz 1st IF and 2 at 455khz, 2nd IF.

In a VHF/UHF Waris there is a 15KHz filter at the 1st IF followed by a 15KHz filter at the second IF and then followed by another filter. It's this last filter that is switched between narrow and wide in the VHF/UHF radios. TX deviation is a setting in programming/alignment.

In the 220 version, there 1st IF is the same, but it's got a 12KHz and then a 9 KHz filter at the second IF.

I've changed out some filters and found it works much better on the ham bands. You need to adjust the squelch for 25khz channels after doing this. The tuner software (2.00.02) will do this for the HT1250 only, it will not work with the mobiles. Use $program to access the greyed out menus in tuner.

HT1250 Filters:

220 front end     44.85MHz       FL3201    MXF45         9180022M10   4-pole +-7.5khz bandwidth
IF2 First filter  455KHz         FL3204    CFUCJ455F     9180468V04   4-pole 12khz                
IF2 filter narrow band filter    FL3206    CFWC455G      9180469V03   6-pole 9khz}}}


The UHF handhelds use the same arrangement, but with a wider middle filter (1st @455). In wide band they switch only the 2nd 2nd IF filter to a narrow band filter.


uhf front end     44.85MHz       FL301    MXF45          9180022M11  
IF2 First filter  455KHz         FL302    CFUCJ455E      9180468V05   4-pole                
IF2 filter wide band filter      FL303    CFWC455E       9180469V05   6-pole
IF2 filter narrow band filter    FL304    CFWC455G       9180469V03   6-pole


The 1st IF is under the shield, and very hard to remove. I've not messed with it, as it appears to be the same part in the UHF, and doesn't look like it's limiting.

Based on the following codes for muratta filters

Muratta filters 
E is +- 7.5 (15)
F is +-6 (12)
G is +- 4.5 (9)

The 220 Filters are 12 and 9 Khz wide at the 2nd IF. Switching them to the E filters of the UHF HT1250 is rather easy, as they are just on the underside of the board, not under a shield. An under board heater with a hot air station makes this rather easy.

Ive found an under-board board pre-heater is mandatory to work with this and 630f at 7 l/m of airflow will prevent hurting the board/parts/

I've found the sensitivity to be a bit better and no squelch clipping on 3.2kc tone at 7khz of deviation (Most ham rigs on 220 have WIDE deviation!).

Software mod

This is easiest with CP tool and a hex editor.

First upgrade the Firmware using the firmware update. This will load the default codeplug back in the radio.

Read the radio using the CP tool and save the binary codeplug. I typically will read this from 0x0000 to 0x1000 which will capture the entire default codeplug (Tuning, Features, and Programing). Save this file and set is aside for safe keeping. If anything goes wrong, you can blow it back into the radio and restore it to defaults with out needing to retune.

Now open up a copy of this code plug and edit it based on the Codeplug Map for the feature blocks. This is from 0x280 to 0x2ff.

You'll need to change the following parts:

  1. Serial number, ASCII spaces are blank (optional)
  2. Channel step needs to be 0x01
  3. Upper Frequency: 0x5F50 for 225 MHz
  4. Signaling: 0xFF is everything enabled (MDC, QCII, DTMF) for trunking and conventional
  5. Conventional Personalities: 0xFF for 255 channels

Once this is done, be sure the checksum 8 on both FDB blocks are 5A. You will need to adjust the checksum bytes for this.

Open this file with the CP tool and put 0x280 to 0x2ff into the radio, no need to write the entire file. This makes it easy to do many units at once, just blow the Feature Block in, while leaving the tuning and programing alone.

You'll need to now tune the 20 and 25 KHz squelch settings in the tuner software. The issue here is the tuner software will not let you select the 20 and 25 KHz from the drop down menu. Using Winabler this can capture the tuner menu and enable these.

I use the auto squelch setup and found a good value is -127.5 dBm for hams. My radio is -124 dBm for 12db SINAD so this is about 6 dB SINAD at -128, very noisy but understandable. Auto tune makes this really easy. You can always program a button to set the squelch to tight in CPS.

I've found I needed to play with the RSSI settings too, as the S meter was setup for commercial strong signal service. I've only seen this with certian 220 radios.

It's also a good idea to check the frequency/modulation/power out alignments too. The CDM1550's from the New Jersey Turnpike all were aligned wrong for the power output, and we 20W out when set for 30W. Align it in tuner properly, and then use CPS to lower the power if you want.

If you've set the serial number to blank, it's a good time to set it to what you want in tuner before you disconnect.

Once you're done with all this, you should have a great radio that covers 216-225 MHz, wide band FM, MDC/QCII/DTMF, 30W power out, and damn sensitive squelch.

Code Plug Map

This is based on the Srecord file loaded as binary

0x000 - 0x27f group, 5A checksum. 0x27f is the checksum byte
This group contains the tuning information for the radios.  
The frequencies it's aligned on are in the same format as the band limits.  
There are 3 groups of frequencies in here, not sure what they all do, but can confirm 
changing them all moved the tuning frequencies on a 6 meter CDM.
0x282 - 0x2D7 - group, needs to be 5A checksum, adjust 0x2D7 to make it.
0x285-0x28E - Serial number
0x291-0x2A0 - Model number, Blank should be spaces 0x20

0x2AC      Channel steps 
*0x01   - 12.5, 20 and 25 KHz
*0x05   - 12.5 only
 
0x2AF       Lower Frequency Limit 
0x2B1       Upper frequency limit 
Desired limit - Base freq (200mhz models the base freq is 103mhz) times 1000 then 
divided by 5. this gives you the new value in dec, you have to change it to hex 
216 MHz is 5848
225 MHZ is 5F50
58485F50 across both bytes


Below is only valid for the 3.08 codeplug tool codeplugs
0x2D8 to 0x2E9 - group, needs to be 5A checksum, adjust 0x2E9 to make it.

0x2E2 - Number of personalities is at in hex.    
*128 - 0x80
*160 - 0xA0
*255 - 0xFF
Below is only valid for the 2.08 codeplug tool codeplugs
0x2D8 to 0x2E4 - group, needs to be 5A checksum, adjust 0x2E4 to make it.

0x2E2 - Number of personalities is at in hex.    
*128 - 0x80
*160 - 0xA0
*255 - 0xFF


The 8 bit checksum must be 0x5A for this bit of code. Byte 0x2E9 is the checksum fix bit. Find the difference after editing between the checksum and 0x5A, then add or subtract this from the value in offset 0x2E9.

Codeplug Map

Waris Codeplug Map
Byte Offset 0 1 2 3 4 5 6 7 8 9 A B C D E F
0x000000 Tuning len Tuning Data
0x000010 Tuning Data Cont.
SKIP SKIP
0x000270 Tuning Data Cont. Checksum
0x000280 Feature len FDB 1 Header Serial Number Null
0x000290 Null Model Number
0x0002A0 Mod Cont. Null CP version CP Source CP Date Chan Step Base Freq Low Frequency
0x0002b0 Low Freq Cont. High Frequency CP Part Number
0x0002c0 CP P/N Cont. Unknown Null Pad TANAPA Unknown
0x0002d0 Unknown Region Checksum FDB 2 Header Trunk Pers Signaling Unknown
0x0002e0 Unknown Conv Pers Unknown Checksum 9
0x0002f0 Unused FDB Checksum

Software

File:HVN9025 v6.12.05.zip Waris CPS 6.12.05

File:R02.02.00 Waris Tuner.zip Waris Tuner 2.02

File:Waris Codeplugtool.zip allows writing and reading raw codeplug from a radio.

File:Unofficial Global Tuner R02.16.05.zip Hacked global tuner for editing the serial number

File:Warisdepot R01.04.00.zip Depot tool to edit serial number and tempeture compensation values.

File:Us waris lab upgradekit r03.08.00.zip Waris Codplug Tool 3.08

File:HT1250LS 217-222 split to 216-225 split.s19 This has problems when going into alignment. DO NOT USE Based on 3.08 upgrade kit (R05.17.01)


HT1250ls 255 Channel, 216-225, 12.5/20/25 step srecord for TANAPA PMUD1760B Blank Serial Number NOTE: DTMF pad doesn't work in this, don't use. Only up here for reference DO NOT USE


HT1250ls 255 Channel, 216-225, 12.5/20/25 step srecord for TANAPA PMUD1761A Blank Serial Number, based on 2.08 Lab Upgrade Kit. This should be used going forward.