Allstar® and P25 on Quantar - Revision history

Bryan: /* Install pnxmono software */

2020-05-16T19:16:29Z

Install pnxmono software

2019-09-16T22:31:15Z

2019-09-16T22:30:50Z

2018-03-26T01:11:59Z

Install pnxmono software

2018-03-26T01:10:42Z

Install pnxmono software

2018-03-25T19:00:36Z

Install pnxmono software

2017-10-13T21:55:33Z

Features

2017-10-13T01:39:27Z

Operational Notes

2017-10-12T09:33:41Z

Files

2017-10-12T09:22:39Z

Channel 2 from Asterisk

@@ Line 467: / Line 467: @@
 chown pnxmono:pnxmono /opt/pnx-mono
 cd /opt/pnx-mono
-su -c 'git clone https://github.com/p25nx/pnx-mono.git' pnxmono
+su -c 'git clone https://github.com/W9CR/pnx-mono.git' pnxmono
 cd pnx-mono
 Now build pnxmono

@@ Line 1: / Line 1: @@
-This is a set of wildcard programing for the Quantar which enables Allstarlink and P25nx linking with mode switching controlled by local traffic.  This is possible via some enhanced wildcard programing, and may be applicable for other users using different controllers.
+This is a set of wildcard programing for the Quantar which enables Allstar® link and P25nx linking with mode switching controlled by local traffic.  This is possible via some enhanced wildcard programing, and may be applicable for other users using different controllers.
 [[File:Front of quantar and controller.jpg|thumb|500px|right|Front of Quantar and controller]]
 == Features ==
@@ Line 30: / Line 30: @@
 ** Alarm output on station alarm.
-* Raspberry Pi controller running both P25nx and Allstarlink DIAL software.
+* Raspberry Pi controller running both P25nx and Allstar® Link DIAL software.
 ** This is behind the cisco 1811 router
 ** Nat rules allow the asterisk port open to the outside.

@@ Line 458: / Line 458: @@
 sudo apt-get update
 sudo apt-get upgrade
-sudo apt-get install git
+sudo apt-get install git dirmngr
 sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 3FA7E0328081BFF6A14DA29AA6A19B38D3D831EF
 echo "deb http://download.mono-project.com/repo/debian stretch main" | sudo tee /etc/apt/sources.list.d/mono-xamarin.list

@@ Line 460: / Line 460: @@
 sudo apt-get install git
 sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 3FA7E0328081BFF6A14DA29AA6A19B38D3D831EF
-echo "deb http://download.mono-project.com/repo/debian wheezy main" | sudo tee /etc/apt/sources.list.d/mono-xamarin.list
+echo "deb http://download.mono-project.com/repo/debian stretch main" | sudo tee /etc/apt/sources.list.d/mono-xamarin.list
 sudo apt-get update
 sudo apt-get install mono-complete mono-devel

@@ Line 462: / Line 462: @@
 echo "deb http://download.mono-project.com/repo/debian wheezy main" | sudo tee /etc/apt/sources.list.d/mono-xamarin.list
 sudo apt-get update
-sudo apt-get install mono-complete
+sudo apt-get install mono-complete mono-devel
 adduser pnxmono --disabled-password
 mkdir -p /opt/pnx-mono

← Older revision	Revision as of 22:31, 16 September 2019
(No difference)

@@ Line 17: / Line 17: @@
 ** Requires PL on receive as defined in the channel.
 ** Repeater has 4 alarm beeps on it in this mode.
-** Loose the analog repeater delay.
+** Lose the analog repeater delay.
 * Mode lock which follows local users keyup after 10 seconds, and locks to that mode (blocks the other) for 5.5 minutes.

← Older revision		Revision as of 01:39, 13 October 2017
Line 1,928:		Line 1,928:

	== Operational Notes ==		== Operational Notes ==
		+
		+	Currently when asterisk is stopped on the host, the GPIO lines go active. This seams like it should be a software fix in the usb driver. Of course if the device is disconnected physically it works fine.
		+
		+	In non-pl mode on analog lock (or post decision channel) the system will repeat p25 data. This is due to fact the channel must be set to analog to block out the Astro wireline. Some IPC between the pnx and asterisk could fix this.
		+
		+	Further when on a analog channel after the initial 10 seconds, a P25 user will cause the analog lock timers to reset. This is true even if in PL mode. In PL mode it will not be repeated, but it will cause the timer to be reset to another 5 min.
		+
		+	When aligning the station you will not be able to set the squelch unless you remove the pertinent wildcard configs. It's best to make a tuning only table for tuning and then reprogram it after it's tuned.

	== Files ==		== Files ==

← Older revision		Revision as of 09:33, 12 October 2017
Line 1,931:		Line 1,931:
	== Files ==		== Files ==
	[[media:Logic PDF for Qunatar and P25.pdf\|11x17 PDF document of diagrams and logic]]		[[media:Logic PDF for Qunatar and P25.pdf\|11x17 PDF document of diagrams and logic]]
		+
		+	[[media:Final_Wiki_Example_Working.cp\|Working codeplug showing this example]]

@@ Line 1,911: / Line 1,911: @@
 |-
 | style="width: 25%;" |'''Input 4'''
-| style="width: 12.5%;" | and not
+| style="width: 12.5%;" |
-| style="width: 25%;" colspan="2" | '''Input 1 '''
+| style="width: 25%;" colspan="2" | ''' '''
 | style="width: 12.5%;" |
 | style="width: 25%; | ''' '''
@@ Line 1,923: / Line 1,923: @@
 |}
-Originally there was "and not Input 2" as well, but this exposed an interesting bug/feature in the wildcard function.  This caused the  failsoft wildcard to be evaluated after the hold off timer switched to channel 1/4/5. As soon as it was run, the system changed back to the decision channel.
+Originally there was "and not Input 2 and not input 1" as well, but this exposed an interesting bug/feature in the wildcard function.  This caused the  failsoft wildcard to be evaluated after the hold off timer switched to channel 1/4/5. As soon as it was run, the system changed back to the decision channel.
 == Operational Notes ==