800 MHz 100W PA

From W9CR
Revision as of 18:59, 26 October 2016 by Bryan (talk | contribs) (→‎Basics)
Jump to navigation Jump to search

The Quantar 800 MHz Power Amp is designed to cover the 850-870 MHz band. It includes a built in single stage circulator and low pass filter

Basics

The Basic module is pictured below.

00 MHz POWER AMPLIFIER MODULE Layout

The major parts of the PA are

  • Printed circuit board
  • Intermediate PA
  • Driver PA
  • Final PA
  • Circulator
  • Low Pass Filter

Each of these parts varies depending on the range of the PA. Note the Circulator is the same between 800 and 900 PA's.

Band IPA DPA FPA Circulator LPF
800 CLF6485A CTF6331A CTF6337A 5884911T06 TFF6280B
900 CLF6485A CTF6348A CLF6496A 5884911T06 TLF7150A

The R3 and R4 module part numbers are the same as what's in a generation one amplifier. R0-R2 is new parts which cover the whole frequency range (380-470 MHz) with the exception of the R2 LPF.

The IPA module is a 1.5 W output that feeds into the DPA. The DPA takes this and ups it to 5-15W depending on the VOMNI control voltage. The passes into the FPA which can output 140-160W. Unfortunately there is no diagram of the IPA or FPA modules.

The FPA module consists of two parallel PA strips with two FET's each for a total of four devices. Each strip is addressed as "A" and "B" in the radio for the current monitoring of the PA.

It's interesting that Motorola is using a part rated for 45W at 960 MHz. They have a total of 180W of power available in this design, and while they loose some in the Wilkerson combiners, it's a very robust design.

Note there is no CPU or even much digital circuitry in the PA. All metering is done via the exciter CPU mostly using an analog input and switches (U4103/4) to switch this input between different voltages on the PA.

The exciter controls the output power by an analog output (V_CONT) 0-5v from the CPU. This voltage is then used to control a couple transistors (Q4100 & Q4101) making the V_OMNI voltage that varies the first stage in the Intermediate PA. [[File:]]

The complete schematics are PNG format and are also available as a PDF

Pictures

This is a UHF R0 Generation 2 PA I took pictures of.

Conversions

PA ID is done via a resistor "ROM". This is a voltage divider on an analog input on the exciter. It appears to be in half volt increments and the exciter split must match the PA.

Note the arrangement of R4164 and R4165 in the layout, they do not go in order!

PA Type PA_ID_A PA_ID_B R4162 R4163 R4164 R4165
UHF 110W R0 0.0 1.5 OPEN 0 390 1k
UHF 110W R1 1.0 0.5 15k 1.5k 560 10k
UHF 110W R2 1.5 0.5 1k 390 100 1k
UHF 110W R3 3.0 1.0 2.2k 2.7k 1.5k 15k
UHF 100W R4 3.5 1.0 18k 15k 1.5k 15k


R0 to R2

Converting from a R0 to R2 is quite easy.

The major components will cover the R2 band fully. The IPA, FPA and circulator are the same with only the LPF being different.

The LPF is different but there is not any problem with using it for R2. I need to test the R0 LPF at R2, as I've not swept the R0, but I suspect it's substantially similar to the R1 Gen 1 module I did sweep.

Below is a sweep of a Gen 1 LPF; R1 & R2 were swept with key data points taken as you can see below.


The only thing necessary to convert the R0 to R2 is to change the ID resistors.


R2 to R0

Should be the same as R1 to R2

R3/4 to R2

I've never seen the R3/4 amp modules. The Gen 2 R3/4 parts are the same as the Gen 1 leading me to believe their may not be a Generation 2 version of these module. This would make sense as only the R0 was added after the fact.

Never attempted. The IPA, FPA, LPF and circulator are different. I would assume the IPA and FPA would be good. The circulator most likely needs to be changed, and harmonics checked, as the LPF cutoff is higher.

If anyone wants to try it and document it, please add it.

R3 to R4 or R4 to R3

Never attempted. The IPA, and FPA are different, but most likely will work as it's a ~5.4% frequency shift. The circulator and LPF are identical on these units so it should be only a matter of changing the ID.